Although it may seem to you that you cannot install
these beautiful expressions, but it is in fact quite easy
to install! There are a few steps, guidelines, and
tricks that you will need to know first though. The
steps below are how we install expressions every day.
Step 1: Determine where you would like the
expression to be installed upon you wall. It is very
wise to measure the expression and the wall you are
thinking about. This will ensure that you expression
will fit on the wall. You can also hold the expression
up to the wall to see what it will look like.
Step 2: Clean and prepare the wall where you plan to
install the expression. A fine mist of a mild cleaning
agent will work best. Lightly, rub the surface of the
wall with a clean paper or cloth towel. This step will
clean any debris or dust that may be located on the
wall.
Step 3: Place the expression upside down on a smooth
and flat surface. A large table, where the entire
expression can lay flat, may suit your needs best.
With the graphic upside down, the backing of the
expression is now on the top. Remove this backing
slowly. It is best to start in one corner and work
towards the opposite corner. Completing this step
will expose the adhesive side of the expression. Be
careful not to let anything touch the adhesive side.
Step 4: Lift the expression up off of the table,
keeping the expression tight and not letting the
adhesive side touch another part of the adhesive or
anything else. This may require an additional helper,
depending on the size of the expression.
Step 5: Position the expression on the prepared site.
Keep in mind that where the adhesive side touches, it
will stay there. Be sure to hold the adhesive side an
inch or two away from the wall. Once you have
determined the exact location of the expression,
slowly press the expression on the wall. It is best to
start in the middle of the expression and go to one
side and then starting back in the middle go all the
way across to the opposite side. After the middle is
pressed, then slowly press the remaining expression
on to the wall in all other areas.
Step 6: You must now squeegee the entire graphic on
to the wall. Perform this step in the same fashion as
the above step, working in the middle first. A firm
amount of pressure will work the best.
Step 7: You can now slowly remove the application
tape from the expression. Slow and steady wins this
race. If while removing the application tape, the
expression does not stick to the wall, go back and
press the expression to the wall. Then, slowly
continue to remove the application tape until the
entire piece of application tape is removed.
That is all there is to it! It may seem difficult and
wordy, but you will find that it is not as hard as you
may have first thought!!
these beautiful expressions, but it is in fact quite easy
to install! There are a few steps, guidelines, and
tricks that you will need to know first though. The
steps below are how we install expressions every day.
Step 1: Determine where you would like the
expression to be installed upon you wall. It is very
wise to measure the expression and the wall you are
thinking about. This will ensure that you expression
will fit on the wall. You can also hold the expression
up to the wall to see what it will look like.
Step 2: Clean and prepare the wall where you plan to
install the expression. A fine mist of a mild cleaning
agent will work best. Lightly, rub the surface of the
wall with a clean paper or cloth towel. This step will
clean any debris or dust that may be located on the
wall.
Step 3: Place the expression upside down on a smooth
and flat surface. A large table, where the entire
expression can lay flat, may suit your needs best.
With the graphic upside down, the backing of the
expression is now on the top. Remove this backing
slowly. It is best to start in one corner and work
towards the opposite corner. Completing this step
will expose the adhesive side of the expression. Be
careful not to let anything touch the adhesive side.
Step 4: Lift the expression up off of the table,
keeping the expression tight and not letting the
adhesive side touch another part of the adhesive or
anything else. This may require an additional helper,
depending on the size of the expression.
Step 5: Position the expression on the prepared site.
Keep in mind that where the adhesive side touches, it
will stay there. Be sure to hold the adhesive side an
inch or two away from the wall. Once you have
determined the exact location of the expression,
slowly press the expression on the wall. It is best to
start in the middle of the expression and go to one
side and then starting back in the middle go all the
way across to the opposite side. After the middle is
pressed, then slowly press the remaining expression
on to the wall in all other areas.
Step 6: You must now squeegee the entire graphic on
to the wall. Perform this step in the same fashion as
the above step, working in the middle first. A firm
amount of pressure will work the best.
Step 7: You can now slowly remove the application
tape from the expression. Slow and steady wins this
race. If while removing the application tape, the
expression does not stick to the wall, go back and
press the expression to the wall. Then, slowly
continue to remove the application tape until the
entire piece of application tape is removed.
That is all there is to it! It may seem difficult and
wordy, but you will find that it is not as hard as you
may have first thought!!
 |  |  |  |  |  |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |